Stump Grinding & Stump Removal in Cross Timber, Texas
Grinding stumps 6–12 inches below grade so the ground can be re-used. Serving Cross Timber and the rest of Johnson County since 2014 — free written estimates, fully insured crews, and complete clean-up.
Do you provide stump grinding in Cross Timber, TX?
Stump Grinding & Stump Removal in Cross Timber, Texas. Grinding stumps 6–12 inches below grade so the ground can be re-used. Most Cross Timber jobs fall between $95 and $600. Tree Service Pros has worked Johnson County since 2014. Free written estimate, full clean-up included, and no work starts without your sign-off.
We have been doing stump grinding work in and around Cross Timber since 2014. A stump left in the ground is a trip hazard, a mower-killer and a termite and Ganoderma host. Grinding is far cheaper than excavating the root plate.
Root plates here are wide and shallow because there is nowhere to go down — limestone is often less than two feet under the grass. That matters for grinding: in Cross Timber the roots run wide and shallow rather than deep, so surface roots often need taking down along with the stump.
- Service
- Stump Grinding
- Area
- Cross TimberJohnson County
- Typical range
- $95–$600per job, varies by site
- Estimates
- Freewritten, no obligation
What is included in Cross Timber
- Ground 6–12 in. below grade for replanting or sod
- Surface-root grinding along walks and drives
- Chip backfill or full haul-off — your call
- Narrow-access machines for gated back yards
- Utility locate before every grind
At a glance
Stump Grinding in Cross Timber — the short version
| Service area | Cross Timber, Johnson County, Texas |
|---|---|
| Population | 362 |
| Soil | shallow alkaline clay over limestone (pH 7.8–8.3) |
| Common trees | live oak, cedar elm, Texas ash, Shumard oak |
| Most common problem | Iron chlorosis |
| Typical cost | $95–$600 |
| Oak pruning window | July – January |
Signs you need stump grinding in Cross Timber
- A stump you keep catching the mower on
- Mushrooms fruiting on old stump wood near the house
- Surface roots lifting a walk or drive
- Wanting to replant, re-sod or build over the spot
- Termite activity in decaying stump wood
Any of these is worth a free look. We will tell you honestly if it can wait.
Grinding versus digging a stump out
Grinding uses a carbide wheel to chew the stump into mulch, typically six to twelve inches below grade — deep enough to plant grass over, and deep enough for most replanting if you cut a fresh hole beside it rather than in it. Excavating the whole root plate with a machine costs several times as much, wrecks the surrounding lawn, and is only necessary if you are pouring a foundation or a pool over the spot.
Pricing
What stump grinding costs in Cross Timber
Most stump grinding work in Cross Timber falls between $95 and $600 for a typical residential job. That is a real range, not a teaser — what puts a job at one end or the other is below.
What moves the price
- Stump diameter measured at the widest point of the flare, not the cut face
- Grinding depth — replanting depth costs more than level-with-grade
- Access; a walk-behind grinder through a narrow gate is slower
- Whether chip is backfilled or hauled off and replaced with soil
- Rock or embedded metal — old fence line stumps are frequently full of wire
The only way to get a real number is for someone to look at it. That visit is free — request an estimate or call (817) 508-9940. Full pricing detail for every service is in our North Texas tree service cost guide.
Local conditions
Cross Timber soil, species and timing
Cross Timber sits on thin, rocky alkaline clay over limestone bedrock — Fort Worth Prairie ground. That drives what grows well here (live oak, cedar elm and Texas ash dominate the older streets) and what goes wrong: iron chlorosis is the condition we are called out for most.
We are regularly within a few minutes of Cross Timber: Burleson (1 mi), Briaroaks (2 mi), Joshua (3 mi) and Keene (7 mi) are all on the same route.
People in Cross Timber search for this as tree stump removal, stump removal, or simply stump grinder in Cross Timber — it is all the same job, and the estimate is free either way.
Timing
Tree care calendar for Cross Timber
| When | What matters |
|---|---|
| Jan–Feb | Best window of the year for structural pruning. Trees are dormant, the framework is visible with the leaves off, and crews are less booked. |
| Feb 1–Jun 30 | Do not prune oaks. Paint any unavoidable wound immediately — storm damage included. |
| Mar–May | Storm season. Straight-line winds find weak unions first. Deadwood and over-extended limbs are worth clearing before it starts. |
| Jun–Aug | Heat and drought stress. Water deeply and infrequently; the thin soil over limestone here dries from the bottom up. Watch for iron chlorosis. |
| Sep–Oct | Root growth restarts as soil cools — the best planting window and a good time for soil correction. |
| Nov–Dec | Leaves down, structure visible. Removals are cheapest now: lighter canopy, firmer ground, less rigging. |
Straight answers
Stump Grinding in Cross Timber — straight answers
What does stump grinding cost in Cross Timber?
Most Cross Timber jobs run $95–$600. Access moves this more than tree size does.
Do you cover Cross Timber?
Yes — Cross Timber is in Johnson County, inside our regular route, 19 miles from our Fort Worth base. Estimates are free and usually within a couple of business days.
When is the right time of year?
Late summer through winter for most work. On oaks it is not optional — nothing between February 1 and June 30, because of oak wilt.
Are you licensed and insured?
General liability and workers' compensation, certificate sent before you book. Texas does not license tree services, which is why that question matters more here than elsewhere.
FAQ
Stump Grinding in Cross Timber — questions we get asked
Can I plant a new tree where the old stump was in Cross Timber?
Not directly in the same hole. Even ground to twelve inches, the remaining root mass decays for years, robs nitrogen as it does, and leaves a void that settles. Plant three to four feet to the side, or grind deep and excavate the chip out and replace with topsoil if the location matters.
Do you remove the roots as well as the stump?
Grinding takes the stump and the surface roots radiating from it. It does not chase lateral roots across the yard — those decay in place over several years and are rarely a problem. If you are building over the spot, tell us and we will price full root-plate excavation instead.
How long does the work usually take in Cross Timber?
Most residential jobs are a single day. A straightforward trim on one or two trees is a half day; a large removal that has to be rigged over a house can run two. We give you a realistic window in the written estimate rather than a hopeful one.
Do you offer discounts for multiple trees?
Effectively yes — the second tree on the same visit costs less than it would on its own because setup, travel and haul-off are already covered. If you have several trees needing attention, get them all quoted at once rather than one at a time.
What payment methods do you take?
All standard forms — card, check, cash and bank transfer. On larger jobs a deposit is normal with the balance due on completion, after you have seen the finished work. We do not ask for payment in full before starting.
Other tree services we provide in Cross Timber
Tree Surgeon in Cross Timber
The climbing, cutting and rigging work — done by people with the credentials to back the name.
Learn more →Brush Removal in Cross Timber
Hauling off brush piles, storm debris and yard-waste stacks.
Learn more →Emergency Tree Service in Cross Timber
Storm response for trees on houses, drives, fences and power drops.
Learn more →Tree Removal in Cross Timber
Safe, insured removal of dead, dying, damaged or badly-placed trees.
Learn more →Shrub & Hedge Trimming in Cross Timber
Shaping, thinning and renewing the shrubs and hedges around the house.
Learn more →Commercial Tree Service in Cross Timber
Property-wide tree work for HOAs, commercial sites, churches and municipalities.
Learn more →Stump Grinding near Cross Timber
We cover the whole corridor, so a job in Cross Timber is rarely a special trip.
See all cities in Johnson County, or our full service area map. Looking for stump grinding across the whole region? See Stump Grinding & Stump Removal.
Standards and sources we work to
- Texas A&M Forest Service — Oak Wilt — The Feb 1 – Jun 30 oak pruning restriction and wound-painting guidance we follow.
- ANSI A300 (Part 1) — Pruning — The national standard our pruning cuts are made to, including the limits on live-canopy removal.
- International Society of Arboriculture — Certification body for arborists. Certifications carry a number the issuer will confirm.
- Tree Care Industry Association — Industry safety standards and accreditation.
- USDA Plant Hardiness Zone Map — North Central Texas sits in zones 8a–8b, which sets what will and will not establish here.
Prices are typical ranges for North Central Texas and are not a quote. Every job is quoted in writing after an on-site visit.
Need stump grinding in Cross Timber?
Free written estimate, usually within a couple of business days. Licensed, insured, and we clean up completely.
Monday–Friday, 8:00 AM – 5:00 PM · Storm and hazard calls are answered outside office hours.